Products
High performance filter
High performance filter designed for large diameter pipelines and high flow rates. It uses a stainless steel pleated filter element as a filter element, the filtration area of which is many times larger than the area of conventional perforated basket filter elements and rod pleated filter elements of competitors.
Description
marker
Description
High performance filter designed for large diameter pipelines and high flow rates. It uses a stainless steel pleated filter element as a filter element, the filtration area of which is many times larger than the area of conventional perforated basket filter elements and rod pleated filter elements of competitors. With an open surface ratio of over 50% and a straight-through design, maximum flow is achieved with minimal pressure drop, significantly reducing overall size and weight. When stopping the filter for maintenance, one person is enough.
How the filter works
The water to be purified enters the housing through the inlet pipe. Impurities are deposited on the stainless steel mesh, resulting in a pressure drop. The differential pressure sensor monitors the change in the difference between the inlet and outlet pipes. When the pressure drop reaches a set value, the electrical controller sends a signal to the hydraulic control valve and the drive motor, initiating the following actions: the motor rotates the brush, which cleans the filter element, and at the same time the control valve opens to discharge contaminants. The entire cleaning process lasts only a few tens of seconds. Once cleaning is complete, the control valve closes, the engine stops, the system returns to its original state and the next filtration cycle begins.
contact us
Related Popular Products
Filter element made of five-layer sintered mesh
The standard five-layer sintered mesh filter element is manufactured primarily by winding filter material based on a standard five-layer sintered mesh.
Composite sintered mesh with perforated sheet
Perforated sheet sintered mesh is a new type of filter media made by composite sintering a perforated sheet of standard material (304 or 316L stainless steel) and multiple layers of square mesh (or twill weave) into a single piece.
Flat aerator
The product is made by welding from a spherical titanium aeration disk, a dense titanium plate and a dense titanium fitting. The spherical titanium aeration disc is sintered from high-purity titanium powder.
Safety fine filter
This filter consists of a cylindrical body and a tube grid. Micropores in the tube sheet are formed by polyethylene (PE) tubes located in it. The filter is assembled in a sealed cylindrical housing. The filtered medium enters the housing through the side inlet and is cleaned through filter tubes, after which the liquid is discharged through the lower pipe.
Multi-cartridge microporous filter
The internal surface of the hygienic microporous membrane filter is mirror polished, which reduces the accumulation of contaminants and makes cleaning easier.
Modular filter
The horizontal bed sheet filter has a long history of use in food and beverage filtration. This filtration method belongs to depth filtration technology and is a modular closed system, especially suitable for low and medium flow rates. Sheet filters with an alluvial layer "Weixian" can be used with various types of filter cakes and are characterized by low cost. Surface treatment fully complies with hygienic requirements.
Hydrophilic pleated filter element made of polytetrafluoroethylene
The filtration membrane is made of hydrophilic polytetrafluoroethylene (PTFE). The product is assembled by heat welding with an internal support frame made of polypropylene or stainless steel. The hydrophilic membrane is resistant to strong acids and alkalis, high temperatures and ozone, suitable for clarifying and sterilizing filtration of highly corrosive, highly oxygenated liquids and organic solvents.
Nylon pleated filter element
The filtration membrane is made of polyamide 6 (nylon 6), the body is made of polypropylene, all components are connected by heat sealing. The membrane is naturally hydrophilic, resistant to alkalis, but not resistant to acids, and has high compatibility with organic solvents; Suitable for filtering liquids, especially alkaline media.
Electrically heated breathing filter
The automatic breathing filter with heating and temperature control is designed in strict accordance with GMP requirements and is a high-tech product independently developed and manufactured by Wenzhou Weixian Light Machinery Co.,Ltd.
Titanium rod filter
The filter housing is made of high quality 316L or 304 stainless steel, the outer and inner surfaces are mirror polished.
Hydrophobic pleated filter element made of polytetrafluoroethylene
The filtration membrane is made of polytetrafluoroethylene (PTFE). The structure with an internal support frame made of polypropylene or stainless steel is assembled using heat welding. The membrane has natural hydrophobicity, is resistant to strong acids and alkalis, high temperatures and ozone, and is designed for gas filtration.
Heat Resistant Corrosion Resistant 316L Stainless Steel Filter Element
Sintered stainless steel powder filter element is manufactured by pressing stainless steel powder followed by high temperature sintering.
Breathing filter
The breathing filter is specially designed and manufactured to ensure sterility during gas exchange in the pharmaceutical and food industries.
316L stainless steel filter element for beer wort aeration
Sintered stainless steel powder filter element is manufactured by pressing stainless steel powder followed by high temperature sintering.
316 Stainless Steel Water Distribution Mesh for Coffee
When brewing specialty coffee, the “secondary distribution grid” is a design element that is often mentioned, but few people fully understand its purpose.
Sintered metal powder filter disc
Powder sintered filtration materials (tubular and slab) are microfiltration elements made from titanium powder Ti and stainless steel grades 304, 304L, 316, 316L by fractionation, molding and sintering.
